iphone water damage repair Hamilton new Zealand apple fix 125 ward street hamilton new zealand

 

iphone water damage repair Hamilton new Zealand

Badly water damaged iphone shorted pp-vdd-boost and pp-lcm-bl-anode this video also explain how to find short using thermal camera and freeze spray

iphone repair specialist in hamilton new zealand.

call 078394111 or visit 125 ward street hamilton New Zealand

mail in Repair read info here https://applefix.co.nz/send-your-device/

logicboard and microsoldering repair courses in New zealand read info here https://applefix.co.nz/logicboard-repair-course/

 

lcd refurbish course read info here https://applefix.co.nz/lcd-refurbish-course/

Nintendo Switch Light NOT Charging Charging port replacement nintendo Switch Repair Hamilton nz

 

Nintendo switch repair experts in hamilton New zealand Call 078394111 or visit 125 ward street hamilton www.applefix.co.nz

Mail in device read instructions here https://applefix.co.nz/send-your-device/

 

logicboard repair courses https://applefix.co.nz/logicboard-repair-course/

 

lcd refurbish courses https://applefix.co.nz/lcd-refurbish-course/

 

How to replace Nintendo switch charging port? read general guide below

Replacing the charging port on a Nintendo Switch can be a bit intricate and requires some technical skill. Here's a general guide on how you might go about it:

 

Tools Required:

Tri-wing screwdriver

Phillips head screwdriver

Tweezers

Plastic pry tool

Replacement USB-C charging port

Heat gun

Soldering Iron

Steps:

Prepare Your Workspace:

 

Find a clean, well-lit area to work in.

Lay down a soft cloth to prevent scratches to the screen or back of the Switch.

Power Down the Switch:

 

Ensure the Nintendo Switch is completely powered off before beginning any repairs.

Remove the Back Panel:

 

Use the tri-wing screwdriver to remove the screws from the back panel.

Gently pry off the back panel using a plastic pry tool. Be careful not to damage the plastic clips holding it in place.

Disconnect the Battery:

 

Inside, you'll find the battery connector. Use a plastic pry tool to disconnect it. This is important for safety reasons.

Locate and Remove the Charging Port:

 

The charging port is typically located at the bottom of the Switch.

Remove any screws securing the charging port in place.

Carefully disconnect any ribbons or cables attached to the charging port.

Replace the Charging Port:

 

Take your new USB-C charging port and connect any ribbons or cables to it.

Secure the charging port in place with the screws you removed earlier.

Reconnect the Battery:

 

Carefully reconnect the battery connector.

Replace the Back Panel:

 

Snap the back panel back into place, ensuring all clips are secured.

Replace the screws using the tri-wing screwdriver.

Test the Switch:

 

Before fully reassembling the Switch, it's wise to test if the new charging port is working properly.

Plug in the charger and ensure the Switch recognizes it and begins charging.

Reassemble the Switch:

 

Once you're sure the charging port is working, you can replace any remaining screws and fully reassemble the Switch.

Tips:

Be Patient: Take your time and don't rush the process. Rushing can lead to mistakes or damage to the device.

Keep Track of Screws: Use a magnetic mat or tray to keep track of screws and small parts during disassembly.

Watch Tutorials: If possible, watch video tutorials or read detailed guides specific to Nintendo Switch charging port replacements for visual guidance.

If you're uncomfortable performing this repair yourself, it might be best to seek assistance from a professional technician or repair service.

ipad pro 10.5" No Display after screen replacement | ipad repair hamilton New Zealand | AppleFix

 ipad pro screen replacement if you not disconnecting the battery most likely you can burn filter or diod, ipad repair hamilton nz call 078394111 or visit 125 ward street hamilton new zealand

We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop. *Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/

logicboard repair course in New Zealand Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology. This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment. Start your own business or increase your chances to get job quickly. https://applefix.co.nz/logicboard-rep... Mail in device info read here https://applefix.co.nz/send-your-device/

https://applefix.co.nz/blog/ipad-pro-105-no-display-after-screen-replacement-ipad-repair-hamilton-new-zealand

laptop dc jack repair | Laptop Not Charging | laptop repairs in Hamilton New Zealand

 Laptop Not turning on or not charging . How to solder DC jack on the cable. Laptop dc jack repairs in Hamilton new Zealand125 ward street hamilton New Zealand Call 078394111Soldering Process for Replacing Laptop DC Jack: Prepare the New DC Jack: Ensure that the new

DC jack is compatible with your laptop model. Examine the soldering points on the new DC jack and make sure they match those on the motherboard. Prepare the Motherboard: Clean the soldering area on the motherboard using isopropyl alcohol and cotton swabs. This removes any dirt, dust, or residue that could interfere with the soldering process. Tinning the Soldering Points: Apply a small amount of solder to the soldering points on the motherboard and the corresponding terminals on the new DC jack. This process is called "tinning" and helps ensure good electrical conductivity during soldering. Positioning the New DC Jack: Carefully position the new DC jack on the motherboard, aligning it with the soldering points. Ensure it sits flush against the motherboard. Soldering: Heat up your soldering iron to the appropriate temperature for soldering electronic components. Hold the soldering iron against the soldering point on the motherboard and the corresponding terminal on the DC jack. Apply a small amount of solder to the joint. The solder should melt and flow smoothly, creating a solid connection between the two components. Repeat this process for each soldering point, ensuring that the connections are secure but not excessively soldered, which could cause shorts. Inspect the Solder Joints: After soldering all the connections, visually inspect the solder joints to ensure they are smooth, shiny, and without any bridges or cold solder joints. Use a magnifying glass if needed to check for any imperfections. Reassembly: Once you're satisfied with the soldering job, proceed with reassembling the laptop following the steps outlined in the previous guide. Testing: Before fully reassembling the laptop, perform a test to ensure the new DC jack is functioning properly. Connect the power adapter and battery and power on the laptop. Check if the laptop charges properly and if there are any issues with the power connection. Final Checks and Cleanup: Once you've confirmed that everything is working correctly, tidy up any loose wires and secure them with electrical tape or heat shrink tubing. Clean the laptop's exterior with a soft cloth and isopropyl alcohol if necessary. By following these steps carefully and using proper soldering techniques, you should be able to successfully replace the DC jack on your laptop. Remember to work slowly and carefully to avoid damaging any components. If you're not comfortable with soldering, consider seeking assistance from a professional technician. or bring it to applefix hamilton new zealand www.applefix.co.nz

ipod Not Charging is it battery or charging Port | ipod touch repair Hamilton new zealand

ipod 6th 7th repair experts in hamilton new zealand . applefix hamilton call 078394111 or visit 125 ward street hamilton

We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop.

*Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/

 

logicboard repair course in New Zealand

Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology.

This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment.  Start your own business or increase your chances to get job quickly.  https://applefix.co.nz/logicboard-repair-course/

 Mail in device info read here https://applefix.co.nz/send-your-device/

iPhone 13 Pro Max rear camera replacement & Safely good LCD removal | iphone rear camera not working applefix

Replacing the rear camera on an iPhone 13 Pro Max requires precision and care. Keep in mind that attempting to replace components on your own may void your warranty, and it's always recommended to seek professional help if you are not confident in your skills. If you're still determined to proceed, here is a general guide for informational purposes only. Please note that the specific steps may vary, and it's crucial to follow the guidelines provided by the device's manufacturer.

Disclaimer: Performing a rear camera replacement on your own may lead to further damage to your device. If your iPhone is still under warranty or AppleCare, it's advisable to contact Apple or an authorized service provider for assistance.

iPhone 13 Pro Max Rear Camera Replacement Procedure:

1. Gather Tools:

• Screwdrivers (Pentalobe and Phillips)
• Plastic or metal spudger
• Tweezers
• Suction cup
• Plastic opening tools

2. Power Off the iPhone:

• Turn off your iPhone before starting the repair.

3. Remove the Screws:

• Use a Pentalobe screwdriver to remove the screws around the device frame.

4. Open the iPhone:

• Use a plastic opening tool or a case opening tool to carefully open the iPhone. Be gentle, and avoid using excessive force.

5. Disconnect the Battery:

• Once the device is open, locate and disconnect the battery to ensure safety during the repair.

6. Remove Logic Board Shield:

• Remove any shields covering the logic board components using a Phillips screwdriver.

7. Disconnect Camera Module:

• Locate the rear camera module and carefully disconnect it from the logic board. Be cautious not to damage any connectors.

8. Remove the Camera:

• Gently remove the old camera from its housing. It may be secured with screws or adhesive.

9. Install the New Camera:

• Place the new camera into the housing and secure it with screws or adhesive.

10. Reconnect Camera to Logic Board:

• Connect the new camera to the logic board using the appropriate connectors.

11. Reassemble the iPhone:

• Reverse the steps to reassemble the iPhone. Ensure all screws are tightened, and connectors are securely in place.

12. Power On and Test:

• Power on the iPhone and test the new camera to ensure it's functioning correctly.

Note: Power on the iPhone and test the new camera to ensure it's functioning correctly. Note: This is a general guide, and the actual procedure may vary. If you are not comfortable or experienced with electronics, it's strongly recommended to seek professional at applefix hamilton 125 ward street hamilton New Zeal

ipad Air NOT charging | U2 Tristar 1610A3 charging ic replacement | ipad repair Hamilton NZ AppleFix

 

ipad air chrging port was replaced but still not charging, tested charging ic 1610a3 was faulty replaced and it charging fine Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology. This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment. Start your own business or increase your chances to get job quickly. read info here https://applefix.co.nz/logicboard-repair-course Mail in device read info here https://applefix.co.nz/send-your-device We specialize in logic board and liquid damage repair and can fix your Laptop, MacBook, mobile phone , ipad, iphone , tablet , playstation, xbox or any other electronic gadget that has been deemed unfixable by another repair shop. *Have a repair shop and are looking to outsource logic board repairs? We offer discounted repairs to other repair shops, schools, large organizations and government agencies. — https://applefix.co.nz/contact/ logicboard repair course in New Zealand Skill development Job Oriented short Training course. In Latest Gadgets, Smart Mobile Phones, Tablets, Laptops, Desktops, gaming gadget, Playstation, Xbox Repair Technology. This course is aimed / focused, to teach you to fix most common repairs an electronics repair shop could face in a practical working environment. Start your own business or increase your chances to get job

 

Replacing the charging IC (Integrated Circuit) on an iPad Air involves intricate soldering work and should be done with caution. If you're not experienced with microsoldering or electronics repair, it's recommended to seek professional assistance, as attempting these repairs without proper expertise can lead to further damage. Here's a general guide for informational purposes only:

Note: This information is for educational purposes, and I am not responsible for any damage that may occur during the repair process. Proceed at your own risk.

Tools and Materials Needed:

1. Replacement charging IC compatible with iPad Air.
2. Microsoldering iron with fine tips.
3. Hot air rework station.
4. Soldering flux.
5. Solder wick or desoldering braid.
6. Tweezers.
7. Magnifying glass or microscope for precision work.
8. Isopropyl alcohol and a brush.
9. ESD-safe workplace and wrist strap.

Procedure:

1. Prepare Your Workspace:
• Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components.
2. Disconnect Power:
• Power off the iPad and disconnect it from any power source.
3. Disassemble the iPad:
• Follow a disassembly guide specific to your iPad Air model to expose the logic board.
4. Locate the Charging IC:
• Identify the charging IC on the logic board. It is typically located near the charging port.
5. Apply Soldering Flux:
• Apply soldering flux to the charging IC and the surrounding components. This helps in soldering and desoldering.
6. Desolder the Old Charging IC:
• Use the hot air rework station and microsoldering iron to carefully desolder the old charging IC. Use solder wick to clean up any remaining solder.
7. Clean the Area:
• Clean the area around the charging IC with isopropyl alcohol and a brush.
8. Place the New Charging IC:
• Carefully place the new charging IC in the correct orientation. Ensure proper alignment.
9. Solder the New Charging IC:
• Use the hot air rework station and microsoldering iron to solder the new charging IC onto the logic board. Be precise to avoid damage to nearby components.
10. Inspect Your Work:
• Inspect the solder joints under a magnifying glass or microscope to ensure they are clean and free of defects.
11. Reassemble the iPad:
• Put the iPad back together in the reverse order of disassembly.
12. Test the Charging Functionality:
• Connect the iPad to a power source and check if it charges properly.

If you are not confident in your microsoldering skills or if the issue persists after the replacement, it's advisable to seek assistance from a professional technician or a reputable repair service. Microsoldering requires precision, and any mistakes could lead to further damage.

 

Macbook pro not turning on A1708 820-00875 shorted 1.8 Volt Line on CD3215B03 | Macbook repair NZ

 

macbook pro A1708 board number 820-00875 moisture damaged | type C power managed IC u3100 CD3215B03 replacement. macbook repair experts in hamilton new zealand applfix call 078394111 visit 125 ward street hamilton new zealand Replacing the USB-C power IC (Integrated Circuit) on a MacBook A1708 involves delicate soldering work and should only be attempted by individuals with experience in electronics repair and soldering. If you're not comfortable with these skills, it's strongly recommended to seek professional assistance. Additionally, performing unauthorized repairs may void any existing warranties. Here's a general guide for informational purposes only. Note that this information is not a step-by-step guide, and specifics can vary based on the nature of the repair and the MacBook model: Tools and Materials Needed: Replacement USB-C power IC compatible with MacBook A1708. Soldering iron with a fine tip. Desoldering wick or solder sucker. Solder. Flux. Precision screwdrivers. ESD-safe workplace and wrist strap. Magnifying glass or microscope for precision work. Procedure: Prepare Your Workspace: Ensure you're working in an electrostatic discharge (ESD)-safe environment to prevent damage to electronic components. Disconnect Power: Power off the MacBook and disconnect it from any power source. Disassemble the MacBook: Follow a disassembly guide specific to the MacBook A1708 model to expose the logic board. Locate the USB-C Power IC: Identify the USB-C power IC on the logic board. It's often located near the USB-C port. Apply Flux: Apply soldering flux to the USB-C power IC and the surrounding components. Desolder the Old IC: Use a soldering iron and desoldering wick or solder sucker to carefully remove the solder from the USB-C power IC's connections on the logic board. Remove the Old IC: Gently lift and remove the old USB-C power IC from the logic board. Be careful not to damage nearby components. Clean the Pads: Clean the solder pads on the logic board using isopropyl alcohol and a brush. Prepare the Replacement IC: Align the replacement USB-C power IC with the solder pads on the logic board and prepare to solder it in place. Solder the New IC: Use the soldering iron to solder the replacement USB-C power IC onto the logic board. Be precise and avoid creating solder bridges between connections. Inspect Your Work: Inspect the solder joints under magnification to ensure they are clean and free of defects. Reassemble the MacBook: Put the MacBook back together in the reverse order of disassembly. Test the USB-C Port: Connect the MacBook to a power source and test the USB-C port to ensure that the replacement IC is functioning correctly. If you are not confident in your soldering skills or if you encounter difficulties during the process, it's strongly recommended to seek professional help. Applefix new zeland are expert in macbook repairs in hamilton new zealand call us on 078394111 or visit 125 ward street hamilton new zealand